Bissell quicksteamer powerbrush pet manual

Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit. With your foot, press the handle release lever on the back of the machine and lay. Carry like a bucket to the sink. Rotate the handle forward to unlatch the lid. Remove lid, turn over and locate built in measuring cup. Fill formula to the indicated fill line on the built in measuring cup and pour into mouth of the bladder. Replace the top of the tank by matching the lid and tank edges.

Handle must be in the forward position in order to replace lid. Rotate the handle to the carrying position to latch the lid. Place tank into machine base, seating firmly in place.

Rotate tank handle back into latched position. Bring machine handle back into upright position. Plug the deep cleaner into a proper outlet and turn the power switch ON I.

The switch is located on the back of the unit. With your foot, press the handle release lever on the back of the lower body of unit. While pressing the spray trigger, make one slow forward wet pass and another back. Caution: Do not over wet. Release the spray trigger and make one slow forward and backward pass over the same area to remove any residual dirty water and aid in drying. Repeat cleaning passes until solution being pulled up appears clean.

Tip: Thorough vacuuming before deep cleaning will prevent early clogging of the lint trap. Turn power switch OFF O. Remove the 2-in-1 water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water.

Remove the top of the tank by rotating the handle forward to unlatch lid and lifting lid off tank. After each use, remove and rinse the lint screen located on the tank lid. If nozzle needs to be rinsed, remove by grasping handle at top and pulling forward. Clean removable nozzle by rinsing under running water.

When finished replace nozzle by slightly raising front of machine to line up slots on the base of the machine with the hooks on nozzle. For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. Unplug the machine and wrap the power cord. After emptying the 2-in-1 water tank, rinse it out at a faucet with running hand hot tap water, taking care to clean underneath and around the heavy duty bladder.

Clean out red lint screen. Removable nozzle may be rinsed if necessary. Any loose hair or debris can be pulled from the brush roll if desired and thrown away. Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. Turn power switch OFF O and unplug from the outlet.

To check if a pump belt has broken, you will need a flat head screwdriver. Insert the blade end into the slot of the belt access door to release. Examine the belt for breakage. You should be able to see the pump belt looped around the motor shaft. Complete installation instructions will accompany the replacement belt. When replacing belt access door be sure to line up slots of belt access door with slots in machine, slide door into place and snap shut.

Refer to Remedy 4 above to check if brush belt or pump belt is broken. Make sure nozzle is on correctly by slightly raising front of machine to line up slots on the base of the machine with the hooks on nozzle.

Attach at base first and then click nozzle into place. Empty tank and refill, refer to. For all other countries, contact your local in country distributor for questions, service, or repair.

If you have questions about your warranty or need replacement parts please contact the numbers below. Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

See Warranty on page 12 for details. Below is a list of common replacement parts. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Cleaning Formula: Refer to bottom of page 4 of this guide for a full selection of cleaning formula available for purchase. This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor.

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Toggle navigation. Deep Cleaner. The carpet shampooing process combines vacuum suction, brushing action, water and cleaning solution to clean beyond the surface of your carpet.

Mark J. Do not remove gasket. Clean nozzle window by lifting latch and removing from machine. Rinse under running water. When finished replace nozzle and secure with latch. It is recommended that every time your solution tank needs refilling, that you empty the contents of the collection tank.

If the collection tank gets too full, you may begin to see foam spitting out of the vent cover. If this happens empty the collection tank.

Remove the collection tank refer to steps 2a and b in the 'To empty the collection tank' section on page 6. Using your thumbs squeeze the 2 grey tabs towards the outside of the unit. Push down at the same time and release. Attach the hard floor tool by hooking it into the front of the removable nozzle and swinging it down until the tabs pop into place. You may store your QuickSteamer this way for the next cleaning task, but never keep soiled solution in the collection tank.

Clean or replace belt. Attach belt to motor pulley and brush, insert brush into right side end cap. Other Maintenance or Service not included above should be performed by an authorized service representative. Contact us directly at NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See 'Warranty' on page 12 for details. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

If you need additional instruction regarding this warranty or have questions regarding what it may. This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Your QuickSteamer is well made, and we back it with a limited oneyear warranty. We also stand behind it with a knowledgeable, dedicated. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

If it will not fit the outlet, have. These items are available for purchase with your model. To order replacement parts or additional tools or formulas, please refer to page Please read this Guide thoroughly before assembling your. Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go.

Decide where to begin — and end — your job. Carpeting will dry in three to four hours, depending on carpet style and air circulation in room. Replace furniture on damp carpeting by placing waxed paper under legs until floor dries completely. Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent-based soil removers should not be used. Always vacuum thoroughly before you deep clean.

If possible, move large furniture to an area you will not be cleaning. With your foot, press the red Power Switch [located in foot of unit] ON. To suction up water, repeat motion over same area without depressing Trigger. See page 8 for instructions. Remove the Collection Tank refer to 3a and b in the Routine Maintenance section on page 8. Push down at the same time and release the Cross Action Brush. Attach the Hard Floor Tool by hooking it into the front of the removable nozzle and swinging it down until the tabs pop into place.

If the Collection Tank gets too full, you may begin to see foam. When this happens you will know it is time to empty the Collection Tank. Release Collection Tank latches [1 each side] by pulling up from bottom of latch and then out. Carry Collection Tank to a toilet or sink. To empty, pour out contents using opening at back of Tank. Remove lint and hair from Red Gasket in base of unit.

Clean Nozzle Window by lifting latch and removing from machine. When finished replace Nozzle and secure with latch. Wipe all surfaces with a soft cloth. Store cleaner upright in a protected, dry area. You may store your QuickSteamer this way for the next cleaning task, but never keep soiled solution in the Collection Tank. Attach belt to Motor pulley and brush, insert brush into right side End Cap. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired.

If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.

Mark J. Bissell President and Chief Executive Officer 2 w w w. See Grounding Instructions. Store indoors. Slide upper body into lower body. Secure with screws. Slide handle assembly down into upper body until it will go no further. Align screw slots. Secure with screw. Place solution tank on back of unit. O peration 3. Before you clean 1. Vacuum carpet thoroughly. A floor fan speeds drying Fill the tank 1. Unscrew the black cap at the bottom of the solution tank.

Place solution tank on lower body. Pre-Treating Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. Wait minutes before deep cleaning.