How to install a door on hinges

If the recess is too deep, the hinge will loosen from the door when it's closed. From your local hardware store, you can buy different types of hinges to suit your needs. To ensure your hinges are positioned correctly, you should trace their shape on both the door and the frame. In most cases, you will cut the recess to match the depth of the hinge. To install door hinges on a new door, use a tape measure to get the correct positions for the top and bottom hinges. You should hold the hinges in place, so the screws go in a straight line.

Connect the door to the doorframe by inserting the hinge. Remember, your door type, and door function will determine the appropriate hinges. Mark the side the hinges need to go on lightly with the pencil. Most doors use only three hinges, but higher doors sometimes use four. Learn pro tips for mounting hinges on projects, such as box lids and small doors.

Place the hinge in the recess and mark where the screws will sit. Fasten the hinges using screws. Sandor nagyszalanczy shows you how to install surface mount hinges, how to. Transcribe marks to the edge of the door or frame at this width with a pencil. To use a level, set the level at the top of the hinge. Place the hinges in line with the guide holes.

Use a butt marker to indicate the proper width for the cut. You can then place your door in the frame and check that the hinge positions on the door and frame line up properly. Install the other half of the hinge along the pencil markings on the door. You should mark the location of the holes on the hinges against the wood and double check to ensure they are accurate. Place the hinges into the mortise and use a pencil through the screw holes to mark them.

Then use a powered drill or a screwdriver to drill narrow holes into the markings. You can then use a screw guide to ensure the screws remain straight as they are put in place. Once the hinges are installed on both the door and the frame, you can set the door into the frame. Make sure the door hinge and the frame hinges line up comfortably before sliding the hinge pins in between. Try swinging the door to ensure the fit is accurate. If your door is shaky, try checking the screws and ensuring that they are tight.

The process for replacing door hinges tends to be easier than installing a brand new hinge. The steps are outlined below. The first step is to open your door wide and expose the hinges. Then you should keep it steady by placing blocks underneath. Next, compare your new hinges against your old ones. You should then unscrew your old hinges starting at the top one. After removing each hinge, you should inspect the quality of the wood underneath.

Next, set your new hinges in place and add the screws using a drill or screwdriver. Repeat this process for the second set of hinges. Finally, test opening and closing your door. If the installation process went correctly, the opening and closing action should be smooth. As you can see, installing hinges is a relatively easy process. If you want to purchase high quality hinges, check out Hinge Outlet. We offer a wide variety of hinges, and can help you find the right one for your needs.

Search 0 Cart. Additional Door Shop All Door Hinges. Shop All Gate Hinges and Hardware. Shop All Cabinet Hinges. Use a drill or screwdriver to drill very narrow pilot holes in the location of the screws you marked on the jamb. Tap them lightly in first, to make sure the screws don't accidentally move out of place. Use a screw guide to keep the screws straight as they go into the wood.

Install the individual hinges. Put the hinges back in their places, and use a drill or screwdriver to secure them individually into the jamb and the door. Connect the door to the jamb.

Hold the door in place, using blocks under the bottom to support it if necessary. Line up the two hinge plates so that the ones on the door match the ones in the jamb.

Slide the hinge pins into place, and remove the blocks from the door. Test the door to make sure it works, and you're finished! Method 2. Use blocks of wood to steady the door. Move the door so that the entire hinge is exposed, and place blocks under the door to steady it. When replacing a door hinge, you won't remove the door. Placing blocks underneath will help support the door and prevent it from falling over.

Compare the hinges and measure the door. Make sure that your new hinges match the old hinges in size and edge shape. Additionally, use a measuring tape to verify that the current hinges are in the right locations. The hinges should be placed so that one is 7-inches from the top of the door frame, and the other is located inches from the bottom of the door-frame. If these are incorrect, you'll need to go about the aforementioned steps on cutting the mortise and preparing the door jamb for the new hinge.

Remove one of the old hinges. Start at the top hinge, and remove the screws holding the hinge leafs in place. Carefully pull them away from the door and the jamb, and check to make sure the wood under the hinges is in good condition. You may want to plug some of the old holes with a small wood wedge, especially if some of the holes have stripped out. Prepare the jamb and door for the new hinge.

If the old door hinge had been attached for some time, you may need to do a little repair work on the jamb and door. Sand down the wood if necessary, and add a new coat of paint or stain to match the pre-existing wood.

If the replacement hinges are sized differently from the old ones, fill in the mortise holes in both the door and the door frame with wood putty. Use a metal scraper to fill in the screw holes or plug them with a small wood wedge. Allow the putty time to dry, and sand it smooth and flush with the surface. Paint or stain the repair to match the rest of the door and trim. Install the new hinge. Place your new hinge over the location of the old one. Use a drill or screwdriver and the package screws to secure the two sides of the hinge to the jamb and the door.

Place the hinge pin in the hinge to secure the new hinge. Repeat the process on the second hinge. Move to the next hinge, and use a drill or screwdriver to remove it. Replace it with the new hinge and new screws, holding it in place to make sure the hinge doesn't get jostled out of location.

Insert the new hinge pin when the new hinges are secured. If you have a third center hinge, you should replace it at this point as well.

Test the new hinges. Remove the blocks from under the door, and try opening and closing it multiple times. If the door opens without any problems, then your job is finished! Mark Spelman Construction Professional. Mark Spelman. If you need to move the hinge, mortise more material as needed and then add wood filler or caulking to fill the void. Not Helpful 4 Helpful I want to put siding on a shed door.

How do I install hinges in a way that will allow the door to open without creasing the siding? In order to prevent the siding from creasing, I recommend beveling the siding edges. Not Helpful 6 Helpful For security reasons, you probably shouldn't put hinges on the outside of a door.

If you did, then people could break in easier because they could just pop the pins out.